For GT35 GT3582 Turbo Charger T3 AR.70/63 Anti-Surge Compressor Turbocharger Bearing

  • * Cost-effective Turbo increase 20-40% power for your car
  • * Ductile Iron QT450-10- Temperature resistance up to 700℃
  • * K418 Alloy- High oxidation resistance& stability (resistance up to 900℃)
  • * Cast Aluminium Blades-Great Air Tightness & Corrosion Resistance
  • * Horse Power Boost up to 600HP
  • * Excellent Design: Durable floating bearing structure & high-precision blade dynamic balance
  • * 100% Balancing Test: This turbocharger you will receive has been balanced using the VSR machine technology
Stock In Stock
Item Number 3002917779

MORE OPTIONS

Combination offer

  • A
  • B
  • C
  • D
  • E
  • F
  • G
Gfor for GT3582-VL
Gfor for GT3582-VL
1
Cost effective turbocharger give your car 20-40% power than a non-turbo car of the same year, make and model
2
Ductile Iron QT450-10, the material used for the exhaust housing, is temperature resistant up to 700℃
3
K418 Alloy, the material used for the exhaust impeller, has high oxidation resistance & stability (resistance up to 900℃)
4
The cast aluminium blades are great airtight seal, airflow, light weight, and corrosion resistant

Introduction

Are you trying to put together a cost effective turbocharger system for your vehicle? You should know a turbocharged car has about 20-40% more total power than a non-turbo car of the same year, make and model. Well, Maxpeedingrods for GT35 for GT3582 turbocharger is excellent for single turbo applications for 4 or 6 Cylinder Engines, Don't hesitate to get a turbo to boost your car's power.

Application

This turbo is a universal application street turbo, some modification may be required based on the individual vehicle.
Perfect for all 4/6 cylinder and 2.5L-6.0L engines
Horse Power: Capable of Boosting Horse Power up to 600HP
** WARNING: Lacking oil will cause turbocharger shaft play and damage, please adjust your oil pressure and make sure turbocharger is fully lubricated

Specification

Exhaust Inlet (Turbo Manifold) Flange: T3 Flange
Exhaust Outlet (Downpipe) Flange: 4-Bolt
Turbine Trim: 84.2
Turbine A/R: 0.63
Turbine Inducer Diameter: 68mm
Turbine Exducer Diameter: 62.4mm
Compressor Trim: 56.9
Compressor A/R: 0.7
Compressor Inducer Diameter: 61.5mm
Compressor Exducer Diameter: 81.5mm
Compress Inlet Size(Air intake): 4 inch (103.5mm)
Compressor Outlet Size: 2.5 inch (63.6mm)
Bearing Type: Wet Float
Cooling Type: Water + Oil
Internal Wastegate: No
Warranty: one year for any manufacturing defects
Compress Inlet Size(Air intake): 4 inches (103.5mm)
Compressor Outlet Size: 2.5 inches (63.6mm)
Wastegate: External Wastegate
Oil Inlet: M10*7/16-24
Oil Outlet: M14.1 & 2*M8*1.25
Water: M14*1.5
Maximum PSI:22
Package Weight: 8350g
Package Size: 26*25*23 cm

Features

1)Product Material:
1. Turbine housing :Ductile iron QT450-10 shell with high-temperature resistance up to 700 degrees Celsius.
2. Steel Turbine Wheel:Made from the special K418 alloy to achieve high oxidation resistance and stability under high temperatures up to 900 degrees Celsius.
3. Compressor housing:ZL104 aluminum.
4. Compressor wheel/blades:
Cast aluminium with good gas tightness and corrosion resistance.
5. Max HP: UP to 600hp.
2)Product Feature:
1. Excellent Design:
Excellent Design And Processing and durable floating bearing structure + high-precision blade dynamic balance.
2. Durable:
Water-cooled/oil-cooled structure extends turbine service life.
3. 100% BALANCING TEST:This Turbocharger you will receive has been balanced using the VSR machine technology.

Installation Suggestions

We highly recommend you make sure the points below before installing:
1.Replace the air filter: if the if the air filter is not replaced may cause the compressor wheel damage.
2.Replace the engine oil: Because floating bearing and turbocharger will be damaged by impurities in the old oil.
3.After large overhaul, the engine cannot be replaced with a new turbocharger because there are too much impurities in oil after overhauling which will damage the replacement turbocharger immediately.
Please run the old turbocharger for 7-10 days and then replace to new turbocharger and new engine oil.

Note

* Replace, repair or reconnect air cleaner element per manufacturer's manual to avoid compressor wheel damage.
* Make sure the oil drain line is lower than the turbo itself.
* Gasoline car must install a water cooling device to avoid overheating.
* Ensure exhaust outlets are well sealed by welding.
* To protect the turbocharger and your car engine, an Air filter is necessary.
* Professional installation is highly recommended.
* For any needs please contact us.
* This is a universal application turbo, so modification might be required for some vehicles.

Write a review

Add photos(0/4)

Note: HTML is not translated!
    Bad 
 Good

Enter your destination to get a shipping estimate.


CONTINUE
*

*Please select a category!

Our friend, the Youtuber HZ Video, currently installed MaXpeedingRods GGT3582 Universal Turbocharger! He shared his using experience, particularly with install guidance.










































DOWNLOAD MAXPEEDINGRODS OFFICIAL App FOR AN ENHANCED EXPERIENCE:

Search "maxpeedingrods" on Google Play or the Apple App Store for downloads

Official Quick Customer Support

Get timely assistance through our official support channel for a seamless experience

Curated Automotive Content Community

Explore hot car topics, connect with enthusiasts, and share favorites

Smart Control

Conveniently manage home devices remotely, such as air heaters and inverter generators

Recommended By
 
"This one has the Billet wheel on it while the other one has the cast and this should spin a lot more efficiently."
--YoungStatic
152K subscribers
 
 
"We're at 16 pounds of boost right now and it's making 500 horsepower so I'm really happy with it."
--Texas Honda Channel
44.7K subscribers
 
 
"This is cnc machined and generally billet wheels such as this one it'll keep the charge temperatures cooler which theoretically would make more horsepower."
--Matthew Chevalier
26.5K subscribers
 
 
"More durable, probably gives you more power and it looks cool in your engine bay."
--FRANCHIZE-EK3 (REDGEAR
14.8K subscribers
 
 
"These turbos now are absolutely sick and reliable I know people that have ran these 200 300 kilowatts and are still running them no issues."
--Rex H
13.1K subscribers
 
 
"I've ran numerous nine second passes with these turbos and have had no problems with them."
--Robby V's Garage
13.1K subscribers
 
 
"This appears to be a nice unit, that will be a good step towards boosting my Iroc-Z with a $200 Turbo!!!"
--GreenLightFilming
47.2K subscribers
 
 
"Yeah it looks like it's a pretty good turbo it's got the the gold Billet upgraded wheels that all the new Max speeding rods high performance turbos have and I believe they're balanced as well yeah it's balanced."
--Rex H
13.1K subscribers
 
Please login or create an account to view
and download the installation.

LOGIN

REGISTER

Forgot password

Login with Email Account